Slick-Pak II Twin-Pak

$570.00

SKU: 97139 Category:
  • Overview
  • Packaging
  • FAQs
  • Advantages
  • Resources

How do you know how much concrete pump primer to make? What happens if you make too much primer? Do you just throw out the excess and waste the material?

Why not try Fritz-Pak’s Slick-Pak II Twin-Pak instead?

The Twin-Pak is the same powerful concrete pump primer and pumping aid, packaged in two, four-ounce water-soluble bags. This allows you to create a smaller amount of concrete pump primer, while also giving you the flexibility to make more if you need it.

Slick-Pak II Twin-Pak works great for smaller concrete pump jobs or for use with line pumps. It is a very popular product for pool builders who are pumping a lot of pool plaster.

Since it is the same product, the Twin-Pak meets all the same standards and applications as the original Slick-Pak II, and is completely safe for your crews and your concrete.

Item# Description
97139Two 4 oz. (113 g.) water soluble bags
How does Fritz-Pak's pumping aid work?
It contains water thickeners and lubricating agents. As Slick-Pak II goes through the pipes and hoses it leaves a coat of water and lubricating agents and effectively wets all surfaces. As the concrete comes behind the Slick-Pak II it does not lose water and the lubrication allows it to slip through the pipe.
What is the difference between Slick-Pak and Slick-Pak II?
Both products have water thickeners and lubricating agents. Slick-Pak has a higher proportion of lubricating agents than Slick-Pak II, thus it is better used as a pump primer. Slick- Pak II has a higher proportion of thickeners, thus it is better suited as a pumping aid, as well as being an excellent pump primer.
Does Slick-Pak II have fluid loss properties?
Yes. The thickeners used in Slick-Pak II work as fluid loss additives in the concrete.
If I have a long run of hose or pipe, should I increase the Slick-Pak II concentration to make it more effective?
No. A too-high concentration may thicken the concrete excessively and produce a plug in the line. It is better to increase the volume of Slick-Pak II used to insure complete coverage and wetting of the line.
What is the best way to prime horizontal lines?
Slick-Pak II will tend to run on the lower part of the line, it is recommended to use a rubber ball in front of the priming solution to avoid only wetting the bottom of the line.
Why do I get plugs when priming for concrete with superplasticizers?
Slick-Pak II requires water to hydrate, so when Slick-Pak II is made with too little water it will absorb water from the concrete in order to hydrate. Concrete with superplasticizers tends to have a low water content, so if the Slick-Pak II absorbs any water from the plasticized concrete, it will have a tendency to plug. For priming for concrete with superplasticizers, we recommend increasing water content be used to prepare the priming solution.
If I do not have a bucket available, can I prepare the priming solution in the hopper?
Yes. Most operators do it that way. Be sure that the bag dissolves completely by directing the water stream over it.
How long in advance do I need to prepare my priming solution?
You need at least 5-10 minutes for the product to dissolve. Once it dissolves, it will stay stable for several hours, so you can prepare your priming solution well before the concrete arrives.
Will it build-up in the pump pipes and hoses?
No.
Can Slick-Pak II be added directly into the Ready Mix truck?
Yes. It will make the concrete more pumpable.
Does Slick-Pak II contain bentonite clay?
No. Slick-Pak II does not contain bentonite or any other type of clay.

Slick-Pak II Twin-Pak improves the efficiency of on site concrete pumping operations.

  • Increased range of pumpability for harsh mixes
  • Reduced risk of concrete plugs
  • Reduced segregation in the mix
  • Minimized slump or air loss during pumping

Adding Slick-Pak products to your concrete pump will also improve the overall profitability of your business.

  • Lower materials cost due to less wasted primer
  • Reduced wear on equipment
  • Reduced costs associated with equipment repair and maintenance
  • Improved efficiency at the job site
  • Better customer relations due to fewer on site issues

Compatibility

Slick-Pak II Twin-Pak is compatible with all standard concrete materials as well as other concrete admixtures. When used with other admixtures, each one must be dispensed separately into the mix.

Applicable Standards

  • ASTM C-494 Type S

Choosing the Right Concrete Pumping Admixture

When is the best time to use Fritz-Pak’s Slick-Pak II Twin-Pak?  David Ojeda explains the best applications for each the different Slick-Pak products in our informative product video.

What's in the box?
(60) Two 4 oz. (113 g.) water soluble bags
We will do our best to maintain shipping costs. If you have questions, please feel free to contact us. Please allow 1-2 weeks for shipping. Orders will be processed the next business day. Orders placed on weekend will be processed on Monday. For expedited shipping, pallet quantities, or bulk packaging options, please contact us directly at onlineorders@fritzpak.com or check with your local distributor. Refunds and returns are subject to a 15% restocking fee. We accept Master Card, Visa, and Discover cards.

You may also like…