When you need a fast, high-viscosity primer for your concrete pump, you can’t beat the speed of Slick-Pak Liquid. Like our other pump primer products, Slick-Pak Liquid creates a thick priming material that evenly coats the inside of your pump. Similar to our powdered concrete pump priming product, our liquid concrete pump primer offers the best protection for your concrete pump. However, the powdered versions can take up to 10 minutes to reach the right consistency. Slick-Pak Liquid is ready for use after only three to five minutes. This is because the materials are already partially hydrated, so it takes less water and less time to reach the desired viscosity.
More About our Liquid Concrete Pump Primer
Check out our product video below to learn more about how our liquid concrete pump primer can help you at your next concrete pumping job. Don’t forget to follow our social media channel to keep up with all the latest news and learn about our other concrete admixtures.
Item#
Description
Bottles/Case
Cases/Pallet
97130
3 oz. (89 ml.) bottles
36
72
What is Slick-Pak Liquid?
It is a specially formulated liquid emulsion of pump primers, pumping aids and water thickeners.
How does Slick-Pak Liquid work?
It contains water thickeners and lubricating agents. As it goes through the pipes and hoses it leaves a coat of water and lubricating agents and effectively wets all surfaces. As concrete comes behind the Slick-Pak it does not lose water and the lubrication allows it to slip through the pipe.
What is the difference between Slick-Pak Liquid and Slick-Pak I & II?
All 3 products have water thickeners and lubricating agents for priming the concrete pumps. The main difference is that in Slick-Pak Liquid the materials are partially hydrated and can become a solution and develop thickness faster than Slick-Pak or Slick-Pak II.
Is Slick-Pak Liquid stronger than traditional Slick-Pak or Slick-Pak II?
No. Slick-Pak II is the strongest material, followed by Slick-Pak and then Slick-Pak Liquid.
Does Slick-Pak Liquid Freeze?
Yes. It will start to freeze around 10 °F (- 12 °C).
Can Slick-Pak Liquid be used after it has been subject to freezing?
Yes. There might be some separation of materials, so be sure to shake well before using.
If I have a long run of hose or pipe, should I increase the Slick-Pak Liquid concentration to make it more effective?
No. A too-high concentration may thicken the concrete excessively and produce a plug in the line. It is better to increase the volume of Slick-Pak used to insure complete coverage and wetting of the line.
What is the best way to prime horizontal lines?
Slick-Pak Liquid will tend to run on the lower part of the line, so we recommend using a rubber ball in front of the priming solution to avoid only wetting the bottom of the line.
Why do I get plugs when priming for concrete containing superplasticizers?
Slick-Pak Liquid requires water to hydrate. When Slick-Pak Liquid is made with too little water it will absorb water from the concrete in order to hydrate. Concrete with superplasticizers tends to have a low water content, so if the Slick-Pak Liquid absorbs any water from the plasticized concrete, it will have a tendency to plug. For priming concrete with superplasticizers, we recommend increasing the amount of water used to prepare the priming solution.
If I do not have a bucket available, can I prepare the priming solution in the hopper?
Yes. Most operators do it that way. Be sure that the bag dissolves completely by directing the water stream over it.
Will Slick-Pak Liquid build-up in the pipes and hoses of the pump?
No.
How do I clean up spills of Slick-Pak Liquid?
The best way to clean up is to absorb the material and then dispose in a regular trash container. Follow with water to ensure all slipperines is removed. You can use sand, dirt, cement, oil absorbers, paper towels, cloth towels, etc.
Is Slick-Pak Liquid safe for the environment?
Yes. For further informatiuon refer to the Material Safety Data Sheet (MSDS).
Does Slick-Pak Liquid contain bentonite clay?
No. Neither bentonite nor any other type of clay.
The liquid mixes into a solution much quicker than its powdered counterparts
No need for expensive ready-mixed priming grout
Packaged in easy to handle 3-ounce bottles, and all cases come with a convenient carrying handle
Increases ease and range of pumpability
Decreases wear on equipment
Easily introduced into pumping equipment
Decreases horsepower required for pumping
Reduces friction and line pressure
Compatibility
Slick-Pak Liquid is compatible with most concrete and cement admixtures. When using more than one admixture, each product should be dispensed separately. Slick-Pak Liquid does not contain calcium chloride, nitrates, or other potentially corrosive materials. Store in a dry location, protected from breakage, deterioration, and contamination.
Rescue-Pak contains six of our most effective admixtures proven to solve problems in the field: Supercizer 5, Slick-Pak II, Super Air Plus, Mini Delayed Set, Super Slump Buster, and Standard Delayed Set.
