Slick-Pak II Twin Pak is a dry powdered concrete pumping aid packaged in two 4 oz. patented, ready-to-use, water-soluble bags. Slick-Pak II is uniquely formulated to provide the concrete pumper with a cost effective method for improving the pumpability of hard-to-pump and harsh concrete and grout mixes. Additionally, this pumping aid product reduces line pressure, improves flow properties, and increases the rate and range of pumpability. It does not contain calcium chloride, nitrates, nitrites, or other potentially corrosive materials, is compatible with all standard concrete admixtures, and is free of bentonite, cementitious materials, soaps, or air-entraining agents.
Learn More About Our Concrete Pumping Aid
For more information about Slick-Pak II, check out the product videos below. Don’t forget to follow our social media channels to learn how our concrete pumping admixtures can make your next pump job easier.
Item#
Description
Bags/Case
Cases/Pallet
97139
Two 4 oz. (113 g.) water soluble bags
60
42
How does Slick-Pak II work?
It contains water thickeners and lubricating agents. As Slick-Pak II goes through the pipes and hoses it leaves a coat of water and lubricating agents and effectively wets all surfaces. As the concrete comes behind the Slick-Pak II it does not lose water and the lubrication allows it to slip through the pipe.
What is the difference between Slick-Pak and Slick-Pak II?
Both products have water thickeners and lubricating agents. Slick-Pak has a higher proportion of lubricating agents than Slick-Pak II, thus it is better used as a pump primer. Slick- Pak II has a higher proportion of thickeners, thus it is better suited as a pumping aid, as well as being an excellent pump primer.
Does Slick-Pak II have fluid loss properties?
Yes. The thickeners used in Slick-Pak II work as fluid loss additives in the concrete.
If I have a long run of hose or pipe, should I increase the Slick-Pak II concentration to make it more effective?
No. A too-high concentration may thicken the concrete excessively and produce a plug in the line. It is better to increase the volume of Slick-Pak II used to insure complete coverage and wetting of the line.
What is the best way to prime horizontal lines?
Slick-Pak II will tend to run on the lower part of the line, it is recommended to use a rubber ball in front of the priming solution to avoid only wetting the bottom of the line.
Why do I get plugs when priming for concrete with superplasticizers?
Slick-Pak II requires water to hydrate, so when Slick-Pak II is made with too little water it will absorb water from the concrete in order to hydrate. Concrete with superplasticizers tends to have a low water content, so if the Slick-Pak II absorbs any water from the plasticized concrete, it will have a tendency to plug. For priming for concrete with superplasticizers, we recommend increasing water content be used to prepare the priming solution.
If I do not have a bucket available, can I prepare the priming solution in the hopper?
Yes. Most operators do it that way. Be sure that the bag dissolves completely by directing the water stream over it.
How long in advance do I need to prepare my priming solution?
You need at least 5-10 minutes for the product to dissolve. Once it dissolves, it will stay stable for several hours, so you can prepare your priming solution well before the concrete arrives.
Will it build-up in the pump pipes and hoses?
No.
Can Slick-Pak II be added directly into the Ready Mix truck?
Yes. It will make the concrete more pumpable.
Does Slick-Pak II contain bentonite clay?
No. Slick-Pak II does not contain bentonite or any other type of clay.
Increases ease and range of pumpability
Decreases wear on equipment
Decreases horsepower required for pumping
Reduces friction and line pressure
Improves mobility and consolidation
Minimizes slump and air loss through pump lines
Reduces dewatering of concrete
Slick-Pak II is packaged in ready-to-use water soluble Fritz-Pak inner bags for convenient use at the plant or job site
Compatibility
Slick-Pak II is compatible with all standard concrete materials as well as other concrete admixtures. When used with other admixtures, each one must be dispensed separately into the mix.
Mortar Set Accelerator is a dry, white, powdered set accelerator packaged for use in pre-packaged mortar or concrete that speeds up set times while increasing early compressive strength.